Behringer Ultrabass BVT5500H Specifications download pdf (Page 7)

12 13ULTRABASS BVT5500H/BVT4500H Quick Start Guide

ULTRABASS BVT5500H/BVT4500H Controls

(3)

(7) (9) (19) (20) (14) (16)

(5) (6) (8) (10) (11) (12) (13) (17) (18) (2) (1)(15)

(3)

(4) (19) (14)(9)

(8) (11) (12) (13) (18) (20) (15) (2) (1)

(21) (26) (32)

(23)(22) (24) (27) (28) (29) (30) (35)(31) (33) (34)(25)

(EN) Controls

(1) POWER switch: Use the POWER switch to turn

on your BVT4500H/5500H.

(2) VTC LED: When the BVT is o, this LED is

notilluminated.

(3) 0 dB jack: To connect an electric bass to the

BVT, use this ¼" mono jack (unbalanced).

Basses with active pickups create

high-level signals.

(4) PAD button (BVT4500H only): If the PEAK

LED (9) constantly illuminates and the GAIN

control (8) is set to 0 (zero), the input level

of the audio signal is too high. In this case,

press this button to activate the pad. The pad

reduces the input sensitivity by 15 dB.

(5) -15 dB jack (BVT5500H only): To connect

an active bass to the BVT5500H, use this ¼"

mono jack (unbalanced).

(6) MUTE button (BVT5500H only): Use this

button if you want to tune a bass without

hearing the tone.

(7) OVERDRIVE button (BVT5500H only):

Usethis button to add a distorted texture to

the audio signal. This feature “overdrives”

theBVT5500Hpreamp.

(8) GAIN control: Use this control to boost or cut

the level of the input signal.

(9) PEAK LED: At various points in the signal path,

the BVT monitors the level of the audio signal.

When the level is too high, the PEAK LED

warns that clipping can occur.

(10) VOICING control (BVT5500H only): To select

the tone you want, turn this knob to one of

the following presets.

The BVT5500H equalizes the audio signal

foryou.

1. Prominent bass and treble tones

(scoopedmids).

2. Smooth and warm treble tones

(passivetone).

3. Flat, natural bass tones (no equalization).

4. Bright treble tones.

5. Flat, natural bass tones that are not

muddy (bass rollo).

(11) – (13) BASS, MID, and TREBLE controls: Foreach

tone (bass, mid-range, and treble) that you

can emphasize or de-emphasize, the BVT

includes a single TONE control.

To emphasize a tone, you can turn the relevant

tone control toward 10 (maximum boost).

Alternatively, you might consider lowering

adjacent bands.

(14) EQ ON button: To turn graphic EQ and level

features, push this button.

(15) EQ faders: If you activated the frequency-band

faders (14), you can use each one to emphasize

and de-emphasize a specic frequency band.

The center frequency of each frequency band

is displayed directly above the relevant fader.

(16) LEVEL fader (BVT5500H only): To compensate

possible level changes of the equalized signal,

slide this control between +12 and -12.

(17) EFFECTS MIX control (BVT5500H only): If you

created an eects loop, use this control to

adjust the dry-wet mix.

(18) MASTER control: To adjust the speaker

volume and the level of the PREAMP OUTPUT,

turn this control toward 0 (no volume/level)

or, alternatively 10 (maximum volume/level).

(19) LIMITER button: The limiter reduces only the

signal peaks that can overdrive the POWER

AMP and distort the audio signal. The limiter

prevents the BVT4500H/5500H from clipping

these signal peaks.

(20) LIMIT LED: When the limiter is activated,

thisLED is illuminated.

(21) Serial number.

(22) Fuse compartment.

(23) Power connector.

(24) Fan: This fan prevents the BVT4500H/5500H

from overheating.

(25) Two ¼" TS (mono, unbalanced) jacks.

(26) A single Neutrik Speakon compatible jack,

forhigh-power loudspeakers. The pin

designation of the speaker is pins 1+ and 1-.

(27) POWER AMP INPUT: To connect an external

preamplier to the BVT, use this ¼" TS jack.

(28) PREAMP OUTPUT: To connect an external

power amplier to the BVT, use this

¼"TSjack.

(29) RETURN jack: To send an audio signal from

an eects processor to the BVT, use this

¼"TS jack.

(30) SEND jack: To send an audio signal from

the BVT to an eects processor, use this

¼" TS jack.

(31) LEVEL control: To adjust the level of any

LINE OUTPUT, turn this knob toward min

(no level) or, alternatively max.

(32) GND LIFT button: To manage the ground

connection between the BVT and a

mixer/recording unit, use this button.

(33) PRE/POST button: To select the

type of signal you want to send to a

mixer/recording unit, use this button.

(34) BALANCED OUTPUT: To connect the

BVT to the mic input on a mixer or,

alternatively to a recording unit, use this

XLR jack(balanced).

(35) TUNER OUT jack: To connect the

BVT4500H/5500H to an electronic tuner,

usethis ¼" TS jack.

Check Out behringer.com for Full Manual

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

Behringer Ultrabass BVT5500H Specifications Page 7

Comments to this Manuals

Related products and manuals for Audio amplifiers Behringer Ultrabass BVT5500H