8 9EUROLIGHT LD6230 Quick Start Guide
EUROLIGHT LD6230 Controls
(1) (2) (3) (4) (5)
(6) (7) (8)
(9) (10) (12) (14)
(13)(11) (15)
(EN) Controls
Control Elements
(1) Ventilation openings are located on the front panel.
Their position at the front assures that hot air does
not enter the inside of your rack, causingequipment
failureor damage.
(2) There is an automated fuse for each of the six dimmer
circles. These fuses engage in the event of overload
orshort circuit.
(3) Use the CHANNEL key to shift between the six
dimmer channels. Whenused in combination with
the CONFIGkey (see (5)), you can select dierent
operating modes (DMX, ANALOG and MANUAL).
(4) Use the UP and DOWN keys to navigate through
individual menus.
(5) The CONFIG key is used to activate the conguration
mode andto select individual menus. When used
in combination with the CHANNEL key (see (3)),
youcanselect dierent operating modes.
(6) The LEDs to the left of the display have two purposes:
supply phase status indication (L1, L2 und L3)
andindication of the operating mode you selected
(DMX,ANALOG and MANUAL).
(7) The 3-digit DISPLAY shows the values to be edited.
(8) The LEDs to the right of the display relate to
the individual menus in the conguration
mode. Dependingon the selected function,
thecorrespondingLED lights up.
(9) When your LD6230 works in DMX mode,
usethe5-pole DMX512 IN-XLR connector to
connectDMX512controlsignals.
(10) You can relay the DMX control signal to additional
dimmer packs by using the 5-pole DMX512 OUT XLR
connector. If the dimmer is at the terminal end of a
DMX chain, place a terminator at the DMX output of the
dimmer pack to avoid signal bounce (use a terminator
with the resistance of 120 Ω between pins 2 and 3).
(11) You can connect an analog 0 - 10 V control signal to
the8-pole ANALOG IN DIN connector.
(12) This is the cable slot for connecting your
lightingequipment.
(13) This is the cable slot for the power supply.
(14) The cooling fan is located here.
(15) SERIAL NUMBER.
Check Out behringer.com for Full Manual
(ES) Controles
Elementos de Control
(1) Los agujeros de ventilación están situados en el panel
frontal. Su posición en el frente garantiza que el aire
caliente no entrará dentro del rack, causandoel fallo o
daño del equipo.
(2) Existe un fusible automatizado para cada uno de los
seis ciclos de regulación. Estos fusibles funcionan en
caso de sobrecarga o cortocircuito.
(3) Use la tecla CHANNEL para cambiar entre los seis
canales de dimmer. Sise usa en combinación con la
tecla CONFIG (vea (5)), puede seleccionar diferentes
modos operativos (DMX, ANALÓGICO o MANUAL).
(4) Use los botones UP y DOWN para navegar en los
menúsindividuales.
(5) La tecla CONFIG se usa para activar el modo
de conguración y para seleccionar los menús
individuales. Si se usa encombinación con la
tecla CHANNEL (vea (3)), puede seleccionar
diferentesmodos operativos.
(6) Los LEDs que se encuentran a la izquierda del display
tienen dos funciones: dar indicación del estado de la
fase (L1, L2 y L3) y dar indicación del modo operativo
que ha seleccionado (DMX, ANALÓGICO o MANUAL).
(7) El DISPLAY de tres dígitos señala los valores que
soneditados.
(8) Los LEDs que se encuentran a la derecha del display
se relacionan con los menús individuales del modo
de conguración. Dependiendo de la función
seleccionada, el LED correspondiente se iluminará.
(9) Cuando su LD6230 trabaja en modo DMX, use el
conector de entrada XLR DMX512 de 5 polos para
conectar las señales de control DMX512.
(10) Puede relacionar la señal de control DMX a dimmer
packs adicionales usando el conector de salida
XLRDMX512 de 5 polos. Si el dimmer está en el
puntoterminal de una cadena DMX, coloque un
terminador en la salida DMX del dimmer pack para
evitar un bote de la señal (use un terminador con
resistencia de 120Wentre los pins 2 y 3).
(11) Puede conectar una señal de control analógica de
0-10Valconector de entrada analógico DIN.
(12) Esta es la ranura para el cable de conexión con
susequipode iluminación.
(13) Esta es la ranura para el cable de alimentación.
(14) Ventilador.
(15) NÚMERO DE SERIE.
Si quiere acceder al manual de instrucciones completo,
vaya a la página web behringer.com
Comments to this Manuals