Behringer K450FX User Manual download pdf (Page 4)

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

2. CONTROL ELEMENTS

1.1.3 Online registration

Please do remember to register your new BEHRINGER equipment

right after your purchase by visiting www.behringer.com

(alternatively www.behringer.de) and kindly read the terms and

conditions of our warranty carefully.

Should your BEHRINGER product malfunction, our goal is to have

it repaired as quickly as possible. To arrange for warranty service,

please contact the retailer from whom the equipment was

purchased. Should your BEHRINGER dealer not be located in

your vicinity, you may directly contact one of our subsidiaries.

Corresponding contact information is included in the original

equipment packaging (Global Contact Information/European

Contact Information). Should your country not be listed, please

contact the distributor nearest you. A list of distributors can be

found in the support area of our website (www.behringer.com).

Registering your purchase and equipment with us helps us

process your repair claims quicker and more efficiently.

Thank you for your cooperation!

ATTENTION!

 High volume levels can damage your hearing or your

headphones. Please turn down the VOLUME control

to zero (all the way to the left) before you power up

the amp. Always make sure you use appropriate

volume levels.

2. CONTROL ELEMENTS

The LEVEL controls adjust the signal level of channels 1 - 4

(K900FX and K450FX: channels 1 - 3).

The four FX controls adjust the channel 1 - 4 signal level at

the input of the integrated effects processor (K900FX and

K450FX: three controls for channels 1 - 3).

The channel 4 signal (K3000FX and K1800FX only) is

normally routed just to the PHONES output without effects.

This way you can practice without being heard, or you

can connect a metronome that you need on headphones

but not on speakers. By pressing the TO MAIN button the

signal will be additionally routed to the speakers without

effects.

By pressing the TO LINE OUT button the channel 4 signal

will be additionally routed to the LINE OUT output without

effects (K3000FX and K1800FX only).

 If you press both the TO MAIN and TO LINE button,

channel 4 will be equal to channels 1 - 3. The signal

will be routed to the speakers and the LINE OUT

output including effects.

The ULTRATONE is equipped with a 7-band graphic

equalizer (K900FX and K450FX: 5-band graphic equalizer).

Use the EQ to adapt the sound to the room acoustics.

Press the FBQ switch to activate the FBQ Feedback

Detection System. The frequencies causing feedback are

shown by the brightly lit fader LEDs. Simply lower the level

of the respective frequency range until feedback

disappears and the LED goes out.

The FX display shows the currently selected preset. The SIG

LED lights up when the effects processor receives an input

signal. When the CLIP LED lights up please reduce the effects

input signal by using the respective FX control(s) .

Turn the FX control to select an effects preset (preset

number starts flashing). Push the control briefly to confirm

your selection.

The LEVEL control in the master section is used to adjust

the main output volume.

Turn the FX RET control to add the effect signal to the main

mix.

Pressing the SHAPE button will add the Shape effect to

the main signal. The Shape function on your ULTRATONE

provides a revolutionary type of filter that you can use to

modify your keyboard sound (K3000FX and K1800FX only).

Use the PHONES jack to plug in your headphones.

The PHONES LEVEL control adjusts the headphones

output level (K3000FX and K1800FX only).

Use the POWER switch to switch the ULTRATONE on or

off. You should always make sure that the POWER switch

is in the “Off” position when initially connecting the unit to

the mains.

To disconnect the unit from the mains, pull out the main

cord plug. When installing the product, ensure that the plug

is easily accessible.

 Please note: Merely switching the unit off does not

mean that it is fully disconnected from the mains.

When not using the unit for prolonged periods of

time, please unplug the unit’s power cord from the

power outlet.

MAINS CONNECTION. Use the power cord supplied with

the unit to connect it to the mains.

FUSE HOLDER/VOLTAGE SELECTOR. Before

connecting the unit to the mains, make sure that the voltage

setting matches your local voltage. A blown fuse should

only be replaced by a fuse of the same type and rating. On

some units, the fuse holder can be switched to one of two

positions, i.e. 230 V and 120 V. When operating the unit

outside Europe at 120 V, a higher fuse rating is required.

The GROUND LIFT switch disconnects (switch pressed)

the ground connection at the LINE OUT output to effectively

eliminate hum noise resulting from ground loops (K3000FX

and K1800FX only).

Use the balanced LINE OUT XLR connectors to feed the audio

signal from your ULTRATONE to a mixing console (K3000FX

and K1800FX only). The LINE OUT signal is post-EQ.

These are the LINE OUT outputs on 1/4" TS connectors

(K900FX and K450FX: one 1/4" TS connector).

 Both XLR and 1/4" TS LINE OUT connectors can be

used simultaneously.

For stereo operation the ULTRATONE features a STEREO

LINK facility. You can connect the OUT of the ULTRATONE

to the LINK IN of another keyboard amp that serves as

slave to achieve true stereo sound. When using the

ULTRATONE as slave, connect the LINK OUT of the master

amp to the IN (K3000FX and K1800FX only).

The SUB OUT connector provides the line-level mono

subwoofer signal for connection to the input of a power

amp or active subwoofer.

Connect your footswitch to the FOOT SW jack, so as to

activate/deactivate the effects processor.

Use the CD IN (K900FX and K450FX: AUX IN) connectors

to connect the output of your CD player, tape deck, CD or

MD walkman. This way you can play along to music or

keyboard tutorial CDs.

These are the LINE inputs for channels 1 - 4 on 1/4" TS

connectors. For mono input signals please use the

L (MONO) connector.

Channel 1 is equipped with an additional XLR MIC input. Due

to internal +15 V phantom power you can even use condenser

microphones. Both XLR and 1/4" TS connectors can be used

simultaneously. In this case the LEVEL control of channel 1

adjusts both the level of the LINE and MIC signal.

SERIAL NUMBER.

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Behringer K450FX User Manual Page 4

Comments to this Manuals

Related products and manuals for Microphones Behringer K450FX