Behringer U-Control UMX250 User Manual download pdf (Page 4)

4 U-CONTROL UMX250 User Manual

1. Before You Get Started

1.1 Shipment

The U-CONTROL was carefully packed at the assembly plant to assure secure

transport. Should the condition of the cardboard box suggest that damage may

have taken place, please inspect the unit immediately and look for physical

indications of damage.

◊ Damaged equipment should NEVER be sent directly to us. Please inform

the dealer from whom you acquired the unit immediately as well as

the transportation company from which you took delivery of the unit.

Otherwise, all claims for replacement/repair may be rendered invalid.

◊ To assure optimal protection of your UMX250 during transport,

we recommend utilizing a carrying case.

◊ Please always use the original packaging to avoid damage due to

storage or shipping.

◊ Never let unsupervised children play with the device or with

its packaging.

◊ Please dispose of all packaging materials in an

environment-friendly fashion.

1.2 Initial operation and power supply

Please make sure that the unit is provided with sucient ventilation, and never

place the UMX250 on top of an amplier or in the vicinity of a heater to avoid the

risk of overheating.

The power supply can be realized in dierent ways depending on the main

application area. For the installation of the UMX250 in a studio environment, it is

possible to connect the device directly to a free USB port of the computer using

the USB cable provided (see Fig. 1.1).

In case it is not possible to establish the power supply over USB (e.g. because of

an overload of the host computer due to several USB devices connected), it is

also possible to operate the UMX250 with three 1.5-Volt batteries (type “AA”,

seeFig.1.2).

Fig. 1.1: Power supply via USB

U-CONTROL UMX250

USB Cable (included)

PC/MAC

Fig. 1.2: The battery compartment on the bottom side of the UMX250

Open the battery compartment by pressing the shutter clamp carefully in

the direction of the battery compartment, while pulling the cover of the

compartment upwards.

Please note the following points when inserting the batteries:

• The +symbol of the batteries must coincide with the +symbol of the

compartment! Incorrect polarity will damage the electronics!

• Do not mix old and new batteries! When you change the batteries,

alwayschange all 3 batteries at the same time.

• Do not use damaged batteries. The UMX250 could be damaged due to the

leakage of chemicals.

• If you do not use the unit for an extended period of time, please remove the

batteries from the compartment. Here again, the batteries could leak and

damage the device.

After inserting the batteries, please close the battery compartment and make

sure the shutter clamp snaps into place again.

If you do neither want to connect the power supply over USB nor operate the

unit with batteries, there is yet another possibility to connect the UMX250 over

an external power pack. Please observe the correct operational data (DC 9 V;

100mA) and correct polarity of the connector plug; you will nd information

about this above the DC input on the rear of the unit. Reverse polarity can

damage theelectronics.

1.3 Online registration

Please register your new BEHRINGER equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warrantycarefully.

Should your BEHRINGER product malfunction, it is our intention to have it

repaired as quickly as possible. To arrange for warranty service, please contact

the BEHRINGER retailer from whom the equipment was purchased. Shouldyour

BEHRINGER dealer not be located in your vicinity, you may directly contact

one of our subsidiaries. Corresponding contact information is included in the

original equipment packaging (Global Contact Information/European Contact

Information). Should your country not be listed, please contact the distributor

nearest you. A list of distributors can be found in the support area of our website

(http://behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eciently.

Thank you for your cooperation!

1 2 3 4 5 6 7 8 9 ... 13 14

Comments to this Manuals

No comments

Behringer U-Control UMX250 User Manual Page 4

Comments to this Manuals

Related products and manuals for Synthesizer Behringer U-Control UMX250