Behringer Eurodesk SL2442FX-Pro User Manual Page 7

  • Download
  • Add to my manuals
  • Print
  • Page
    / 17
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 6
EURODESK SL3242FX-PRO/SL2442FX-PRO
Control elements and connections 7
Stereo channel fader and othercontrol elements2.2.4
Channel fader, balance control, mute switch, etc.Fig. 2.7:
(22) The BAL(ANCE) control has the same function as the PAN
control on the mono channels. It determines the relative
volume of the left and right input signals before they are
routed to the stereo main mix bus (or to two su/jointfilesconvert/335959/bgroups).
All other control elements of the stereo channels work in the same
ways as their counterparts on the mono channels (faders, MUTE
switches, etc.).
Please note: When you route a stereo channel to the +
su/jointfilesconvert/335959/bgroups using the SUB switches, please be sure to
set the BAL control to its mid position, so that the signal
is sent to two su/jointfilesconvert/335959/bgroups and remains stereo.
Stereo channels 21 - 24 (SL2442FX-PRO) 2.3
or 29 - 32 (SL3242FX-PRO)
Auxiliary stereo channelsFig. 2.8:
Your EURODESK has two stereo channels with an aux send
section ((23) AUX 1 and AUX 2) and one LEVEL control (24). For
these channels, the aux buses are hard-wired to pre-fader and are
therefore particularly useful for monitoring. They have no routing
switches and are always sent to the main mix. Like the normal
stereo channels they have two line-level inputs on1/4" TRS con-
nectors for the left and right channels, and a SOLO switch.
Similar to the CD/TAPE inputs (see (49)) the auxiliary stereo
channels can be connected to CD players, tape decks, etc., for
example, to feed in playback material.
Su/jointfilesconvert/335959/bgroups 1 - 42.4
Su/jointfilesconvert/335959/bgroups 1 - 4Fig. 2.9:
The EURODESK has 4 su/jointfilesconvert/335959/bgroups enabling you to create mono or
stereo mixes from multiple input signals. Su/jointfilesconvert/335959/bgroups are controlled
from one (mono) or two (stereo) su/jointfilesconvert/335959/bgroup faders. Additionally, it
is possible to connect the su/jointfilesconvert/335959/bgroup outputs as tape sends to a
multi-track recorder.
(25) The su/jointfilesconvert/335959/bgroup faders determine the volume of the su/jointfilesconvert/335959/bgroup
signal at the su/jointfilesconvert/335959/bgroup output (28). Depending on the position
of the routing switch (27) you can thus control the su/jointfilesconvert/335959/bgroup
volume in the main mix.
(26) The SOLO switch routes the su/jointfilesconvert/335959/bgroup signal to the solo
bus (Solo In Place) or PFL bus (Pre Fader Listen), so that
you can monitor the su/jointfilesconvert/335959/bgroup signal without affecting the
main or sub output signals. The signal to be monitored is
taken either pre (PFL, mono) or post-su/jointfilesconvert/335959/bgroup fader(Solo,
stereo), depending on the position of theSOLO/PFL switch
(40)). The SOLO LED illuminates when the SOLO switch is
pressed.
(27) Use the routing switches for the su/jointfilesconvert/335959/bgroups to send the
su/jointfilesconvert/335959/bgroup signal to the main mix. You can route it to the
left stereo side (=LEFT pressed), to the right stereo side
(=RIGHT pressed) or to both (=LEFT and RIGHT pressed).
For example, when you have created a stereo submix using
su/jointfilesconvert/335959/bgroups 1 and 2, be sure to route group 1 to the left and
group 2 to the right side to maintain proper stereo position-
ing. If it is a mono submix with just one su/jointfilesconvert/335959/bgroup, route it to
the left and right sides of the main mix to make the signal
audible on both sides.
Su/jointfilesconvert/335959/bgroup outputs 1 - 4Fig. 2.10:
(28) These four SUBGROUP OUT (puts) carry the signals of the
individual su/jointfilesconvert/335959/bgroups. For multi-tracking connect the outputs
to the inputs of a multi-track recorder (see chapter 4.1 “Studio
set-up”).
Page view 6
1 2 3 4 5 6 7 8 9 10 11 12 ... 16 17

Comments to this Manuals

No comments