Behringer U-Control UMX610 User Manual download pdf (Page 10)

10 U-CONTROL UMX610/UMX490 User Manual

The enormous value range of a total of 128 x 128 = 16,384 dierent values is

therefore available to you via the BANK SELECT command. This theoretically

means that you could use external devices which support the same amount of

dierent banks.

If you consider that each of these banks again contains another 128 individual

programs, you will receive the unbelievably large number of 2,097,152 dierent

options to organize these programs.

1) Press the ASSIGN push-button and hold it down.

2) Press one of the 16 channel keys ( CH 1 ) through ( CH 16 ), orpress the

( GLOBAL ) key.

3) Release the ASSIGN push-button.

4) Press the

BANK MSB

key. Then press the number keys in sequence until

you have completely entered the desired BANK MSB number. Only value

entries between 0 and 127 are possible. Greater values are ignored by

the device.

The BANK MSB has now been dened.

Examples:

• Press ( 1 ) and ( 4 ) if you have decided on MSB 14, forexample.

• Press ( 1 ), ( 0 ) and ( 7 ) if you would like to select MSB 107.

5) Now dene the

BANK LSB

by pressing the key. Then enter the number

value of the BANK LSB with the already familiar procedure (see step 4).

Thesame entry rules apply as for the BANK MSB.

You have dened the bank in which the desired program will be called

up in steps 4 and 5. Now all you have to dene is the program itself:

6) Press the

PROGRAM

key and then press the number keys in sequence

until you have completely entered the desired program number.

Onlyentries between 0and 127 are possible, greater values are ignored

by the device.Ready!

7) Finally, press the ENTER key. In order to discard your assignments,

pleasepress the CANCEL key or press the ASSIGN push-button again.

TheASSIGN LED will go o in all 3 cases.

Example:

You want to select preset No. 49 in bank 25 of an external device on channel

14 via the UMX. Only the LSB will be used to describe the bank, since the bank

number remains less than 128. The MSB in this case equals 0.

1) Press and hold the ASSIGN push-button.

2) Press the channel key ( CH 14 ).

3) Release the ASSIGN push-button.

4) Then, press the

BANK MSB

key or the ( 0 ) key

5) Press

BANK LSB

key and then describe bank 25 with push-buttons ( 2 )

and ( 5 ).

6) Dene the program: Press the

PROGRAM

key and then the ( 4 ) and

( 9 ) keys for program 49.

7) Press the ENTER key.

c) Direct program selection through the two OCTAVE SHIFT

push-buttons.

1) Press the ASSIGN push-button and hold it down.

2) Select the OCTAVE SHIFT push-button which you want to assign to the

program change function.

3) Release the ASSIGN push-button again.

4) Dened the channel by which the program change will be transmitted.

Press one of the 16 channel keys ( CH 1 ) through ( CH 16 ) on

thekeyboard.

5) Press the

PROG DIR

key. Then press the number keys on the

keyboard in sequence until you have completely entered the desired

preset number. Onlyvalue entries between 0 and 127 are possible.

Greatervalues are ignored by the device.

6) Finally, press the ENTER key. In order to discard your assignments,

pleaseselect the CANCEL key or press the ASSIGN push-button again.

TheASSIGN LED will go o in all 3 cases.

◊ As soon as you have assigned the direct program selection to one

or both OCTAVE SHIFT push-buttons simultaneously, pressing both

push-buttons will not activate ANYTHING!

4.2.9 Other functions of the octave shift buttons

The OCTAVE SHIFT push-buttons of the device are in their initial state every time

the UMX is switched on (see Table 3.1). Further special functions can be assigned

to both push-buttons in the ASSIGN mode in addition to the already covered

functions regarding direct program change and octave transposition:

a) Transposition in individual semitone steps

b) Sequential scrolling in program libraries

c) Optional controller functions

◊ As soon as you assign a function to one of the two push-buttons,

the second push-button will automatically assume the same function,

however, it is still restricted in its functionality. It is not capable of

sending data until you assign a function to this push-button with the

ASSIGN procedure.

a) Transposition in individual semitone steps

1) Press the ASSIGN push-button and hold it down.

2) Press the

TRANSP +/-

key.

3) Release the ASSIGN push-button.

4) Finally, press the ENTER key. In order to discard your assignments,

pleasepress the CANCEL key or press the ASSIGN push-button again.

TheASSIGN LED will go o in all 3 cases.

Pressing the right hand one of the two push-buttons causes a shift by one

semitone upward pressing the left hand one leads to a shift by one semitone

downward. Pressing both push-buttons cancels all transpositions.

◊ A keyboard can consist of a maximum of 128 semitones according to

the MIDI standard. If you have reached the lower or upper end of this

tone range with the transposition function, you cannot exceed the

highest or lowest tone despite continued pressing of the transposition

push-button. This also applies to the transposition in octave steps.

1 2 ... 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Behringer U-Control UMX610 User Manual Page 10

Comments to this Manuals

Related products and manuals for Digital pianos Behringer U-Control UMX610