12 EUROCOM ST2600/ST2400NANO/ST2400/ST208S 13 Quick Start Guide
(EN) Step 2: Installation
EUROCOM ST2600/ST2400NANO/ST2400/ST208S Ins tallation
Contents:
• ST Series loudspeaker assembly (2)
• Cover grille (2)
• Split C-ring backing plate (2)
• C-ring support bar (4)
• Support bar mounting screws (4)
• Conduit clamp (2)
• 4-pole Euroblock connector (2)
• Cut-out template (1)
Suspended Tile Ceiling
Use the cut-out template to
mark the nished side of the tile,
thencut out the hole,
workingfrom the nished side of the
ceilingtile.
Place the loudspeaker face
down, then place the ceiling tile
nished side down over the
speaker and onto the bezel rear.
Remove the connection cover
screw on the rear of the
back-can and swing the cover
open to access the connection well.
Terminate the wiring per the
instructions in the Connections
section. Insert the 4-pole
Euroblock connector into the mating panel
mount connector.
Replace the connection cover
and re-install the screw.
Position the ceiling tile and the
attached loudspeaker
assembly into the ceiling grid.
Ensure the C-ring support bars are resting
on the metal ceiling grid.
Set all front panel controls.
SeeControls and Settings
section for details.
After all front panel controls
have been set, ax the grille
to the assembly by aligning it
to the bezel and rmly pressing around the
grille edges until it is securelyseated.
**An optional Plaster Ring accessory is
available for new construction installations.
View the full manual on behringer.com
fordetails
LOUDSPEAKER MOUNTING
INSTRUCTIONS –
FORQUALIFIED
PERSONNEL ONLY
This loudspeaker system may be
permanently installed by qualied
personnel, using approved methods and
materials. Improper installation can pose
serious risk of injury or death. Please read
these instructions in their entirety before
attempting installation.
Permanent installation may only be
attempted by persons licensed and
qualied by appropriate authorities
governing the installation location.
Installers are to employ only original
parts, brackets, fasteners and suspension
accessories or properly rated and certied
components from third parties. Replace any
missing parts by contacting the authorized
Reseller or Distributor in your region.
Clarifyall local requirements and obtain
necessary approvals and permits before
commencing work.
When selecting a location for the
loudspeaker to be installed ensure that
all mechanical, acoustic and safety
considerations are observed. Ensure that
the structure is capable of supporting
the load and that all hardware is rated
accordingly with ample safety factor.
Do not suspend loudspeaker over areas
of public circulation or where failure of
the suspension system can cause bodily
or property damage. Inspect suspension
hardware regularly to ensure integrity.
Loudspeakers radiate a magnetic
eld, even when they are not in use.
Thismagnetic eld may cause interference
with other devices such as computers,
magnetic media and certain types of video
monitors. Maintain a spacing of 2 meters
between the loudspeaker and any such
devices to preventinterference.
MUSIC Group, its aliates and
representatives shall not be liable for any
property damage or personal injury arising
from the improper installation, use or
maintenance of this product.
C-Ring
Loudspeaker Assembly
Support Bars
Position the included support
bars evenly across the ceiling tile
with the screw holes facing
theloudspeaker.
Place the C-ring over the
loudspeaker so the connecting
ears t over the pre-drilled rails,
and then install the supplied
mountingscrews.
Rotate the loudspeaker
assembly so the mounting
clamps are aligned to the
clamping surface of the C-ring, not the
splitopening.
Turn the clamp screws located
on the front face of the speaker
clockwise to deploy the
mounting clamps and tighten them to
theC-ring.
Ear
C-Ring
Loudspeaker Assembly
Support Bars
Ceiling Tile
Clamps
C-Ring
HR
FR
LO
-
Z
Comments to this Manuals